| 1 | Part#: | VMA-C210YTH |
20080115 00012102 |
| 5 | Dimensions: | Please See Note |
20070505 00012106 |
| The dimensions of the Horizontal Stabilizer include the mounting Saddle and Elevator unless otherwise noted. The Elevator Quantity is the number of elevator segments. This is usually 1 or 2. i.e. 1 if the elevator is one piece, 2 if the elevator is split into a right and left segment. The Elevator Length is expressed as the length per elevator segment. The Elevator Area is expressed as the total of the area of all elevator segments. | |||
| 6 | Terminology: | Please See Note |
20070505 00012107 |
| The term "effective" is used to desribe the size of an object which is tapered or irregularly shaped. The term "chord" describes the linear distance from the leading edge to the trailing edge through a wing or control surface. The terms "saddle" and "saddle area" describe that portion of a flying surface such as the center section of a wing or horizontal stabilizer where it intersects the fuselage. | |||
| 9 | Horiz Stabilizer Location: | Horizontal Stabilizer slot in aft end of Fuselage |
20070505 00012110 |
| 10 | Horiz Stabilizer Span Tip to Tip: | 18.86 in. (479 mm) |
20070503 00012111 |
| 11 | Horiz Stabilizer Span (effective): | 14.96 in. (380 mm) |
20070503 00012112 |
| 12 | Horiz Stabilizer Chord Maximum: | 6.06 in. (154 mm) |
20070507 00012113 |
| 13 | Horiz Stabilizer Chord at outboard end of Elevator: | 3.78 in. (96 mm) |
20070507 00012114 |
| 14 | Horiz Stabilizer Chord (effective): | 4.92 in. (125 mm) |
20070507 00012115 |
| 15 | Horiz Stabilizer Area: | 73.63 sq in. (475.00 sq cm) |
20070507 00012116 |
| 16 | Horiz Stabilizer Area relative to Wing Area: | 18.65 % |
20070507 00012117 |
| 17 | Horiz Stabilizer Length of Saddle: | 3.58 in. (91 mm) |
20070503 00012118 |
| 18 | Horiz Stabilizer Width of Saddle: | .79 in. (20 mm) |
20070503 00012119 |
| 19 | Horiz Stabilizer Area of Saddle: | 2.82 sq in. (18 sq cm) |
20070503 00012120 |
| 20 | Horiz Stabilizer Area without Saddle: | 70.80 sq in. (456.80 sq cm) |
20070507 00012121 |
| 21 | Horiz Stabilizer Area without saddle relative to Wing Area without wing saddle: | 19.15 % |
20070507 00012122 |
| 22 | Horiz Stabilizer Airfoil Shape: | Slab |
20070503 00012123 |
| 23 | Horiz Stabilizer Thickness Maximum: | .169 in. (4.3 mm) |
20070503 00012124 |
| 27 | Horiz Stabilizer Taper along Leading Edge: | Yes. Rounded |
20070503 00012128 |
| 28 | Horiz Stabilizer Taper along Trailing Edge: | Yes. Rounded |
20070503 00012129 |
| 29 | Horiz Stabilizer Material: | Balsa Wood & Light Plywood. Ribs, Formers and Sheeting are Laser Cut. Sticks, Stringers & Strips are Saw Cut. |
20070503 00012130 |
| 30 | Horiz Stabilizer Construction Method: | Built Up |
20070503 00012131 |
| 31 | Horiz Stabilizer Construction Adhesive: | PVA, Cyanoacrylate and Epoxy |
20070503 00012132 |
| 32 | Horiz Stabilizer Sheeted Fully: | No |
20070503 00012133 |
| 37 | Horiz Stabilizer Attaches to Fuselage via: | Slot in Fuselage and Adhesive |
20070503 00012138 |
| 38 | Horiz Stabilizer Adhesive Required: | 30 Minute Epoxy |
20070503 00012139 |
| 39 | Horiz Stabilizer Requires Struts: | No |
20070503 00012140 |
| 40 | Horiz Stabilizer Elevator Factory Installed: | Yes |
20070503 00012141 |
| 41 | Horiz Stabilizer Elevator Quantity: | 1 (i.e. not split into left & right halves) |
20070503 00012142 |
| 42 | Horiz Stabilizer Elevator Length (effective): | 17.32 in. (440 mm) |
20070503 00012143 |
| Horiz Stablizer Elevator Length is 480 mm at the hinge line (closest to the wing). The Elevator Length is rounded at the trailing edge | |||
| 43 | Horiz Stabilizer Elevator Chord (effective): | 2.40 in. (61 mm) |
20070503 00012144 |
| Horiz Stabilizer Elevator Chord varies continuously due to rounded edges throughout. | |||
| 44 | Horiz Stabilizer Elevator Area: | 41.60 sq in. (268 sq cm) |
20070503 00012145 |
| 45 | Horiz Stabilizer Elevator Area relative to Wing Area: | 10.54 % |
20070506 00012146 |
| 46 | Horiz Stabilizer Elevator Area relative to Wing Area without wing saddle: | 11.25 % |
20070506 00012147 |
| 47 | Horiz Stabilizer Elevator Area relative to Horiz Stabilizer Area: | 56.51 % |
20070507 00012148 |
| 48 | Horiz Stabilizer Elevator Area relative to Horiz Stabilizer Area without saddle: | 58.76 % |
20070507 00012149 |
| 49 | Horiz Stabilizer Elevator Hinges per Elevator: | 4 |
20070503 00012150 |
| 50 | Horiz Stabilizer Elevator Hinge Type: | Flexible Live Low Gap |
20070503 00012151 |
| 51 | Horiz Stabilizer Elevator Hinge Adhesive: | Cyanoacrylate |
20070503 00012152 |
| 52 | Horiz Stabilizer Elevator Hinge Material: | Proprietary Super Strong |
20070503 00012153 |
| 54 | Horiz Stabilizer Elevator Servo Required: | Yes 1 Sub-Micro |
20070503 00012155 |
| 55 | Horiz Stabilizer Elevator Servo Location: | Tray in centre of fuselage |
20070503 00012156 |
| 56 | Horiz Stabilizer Elevator Servo Mounting Method: | Tray (Wood) |
20070503 00012157 |
| 60 | Horiz Stabilizer Color Top Schema: | Monochrome |
20070503 00012161 |
| 61 | Horiz Stabilizer Color Top Main: | Yellow |
20070503 00012162 |
| 65 | Horiz Stabilizer Color Top vs Bottom: | Similar |
20070503 00012166 |
| 66 | Horiz Stabilizer Color Bottom Schema: | Monochrome |
20070503 00012167 |
| 67 | Horiz Stabilizer Color Bottom Main: | Yellow |
20070503 00012168 |
| 71 | Horiz Stabilizer Weight: | .099 lbs (45 g) |
20070503 00012172 |